Hey all
I am bringing you all an affordable answer to a PERFECT z31 Big Brake Kit.
This will fit all hubs for the z31 including the non-turbo and turbo hubs from both Zenki and Kouki models!!
Also, these Brembo Calipers require the use of a banjo bolt type brake line setup.... so in other words, you can use the stock/factory z31 lines! I personally have SS z31 lines.
Here is what you need:
1 - EVO 8/9 or WRX STI (compatible years) Brembo Calipers
2 - S13 (or similar) to EVO Brembo Bracket
http://madparts.net/evo-brembo-caliper-brackets.html
If you order from madparts.net, note that Alex sent you there!
3 - 1994-2004 Ford Mustang Cobra 13" Rotors (I chose 2002 to be safe)
Here are the modification notes
1 - You will need to grind a bit of the aluminum webbing on the back of caliper to clear the bracket
2 - Depending on how much you grind on the back of the caliper, you may need to grind some off the brackets.
3 - You will need to flip the EVO Brembo bracket upside down (to raise the caliper a bit higher)
4 - With Kouki Turbo hubs, no spacing or shimming is required. But with Zenki hubs, you may need to space or shim the calipers. You will need longer studs when using the Zenki/non-turbo hubs.
Also, beware that if you run the Zenki hubs, the rotor and caliper will be approx. 14mm out further.
5 - Also I should add that the from the top hat of the rotor to the face of the caliper, it is 1.5". You may need a wheel spacer to accommodate this larger caliper.
I have always ran 25mm (1") wheel spacers, so for me, this isn't an issue.
Thats it.
I am bringing you all an affordable answer to a PERFECT z31 Big Brake Kit.
This will fit all hubs for the z31 including the non-turbo and turbo hubs from both Zenki and Kouki models!!
Also, these Brembo Calipers require the use of a banjo bolt type brake line setup.... so in other words, you can use the stock/factory z31 lines! I personally have SS z31 lines.
Here is what you need:
1 - EVO 8/9 or WRX STI (compatible years) Brembo Calipers
2 - S13 (or similar) to EVO Brembo Bracket
http://madparts.net/evo-brembo-caliper-brackets.html
If you order from madparts.net, note that Alex sent you there!
3 - 1994-2004 Ford Mustang Cobra 13" Rotors (I chose 2002 to be safe)
Here are the modification notes
1 - You will need to grind a bit of the aluminum webbing on the back of caliper to clear the bracket
2 - Depending on how much you grind on the back of the caliper, you may need to grind some off the brackets.
3 - You will need to flip the EVO Brembo bracket upside down (to raise the caliper a bit higher)
4 - With Kouki Turbo hubs, no spacing or shimming is required. But with Zenki hubs, you may need to space or shim the calipers. You will need longer studs when using the Zenki/non-turbo hubs.
Also, beware that if you run the Zenki hubs, the rotor and caliper will be approx. 14mm out further.
5 - Also I should add that the from the top hat of the rotor to the face of the caliper, it is 1.5". You may need a wheel spacer to accommodate this larger caliper.
I have always ran 25mm (1") wheel spacers, so for me, this isn't an issue.
Thats it.
Comment