VG33 and 6 individual coils mounted

[Rick88ss]

Been working on the Z yesterday and today and here's the progress with the VG33ET and mounting the 6 individual coils for the Microtech LT-12s with external X6 ignition box.

[ikonmy]

looks verry nice and clean
good luck

[SATAN]

That looks SOOO GOOOD! very clean too. What are your plans for your oil catch can? I see you currently have the outlet pointed toward the back of the bay???

Who makes those coils? I love how you have 3 one one side and 3 on the other. Very nice job. very clean. I even like the knock off NISMO oil cap. I may have to get me one of those!

Wait a second, what are you going to do about a battery hold down now? Or is there still room behind that coil for one to fit?

Do you got a pic of the whole engine bay the way it sits right now? I can see you got some money sitting in all of those AN fittings. You did the same thing on your fuel rails that I did. As far as bolting them down I mean.

[MrwassmanNA2T]

Your car looks edible

[SteveZ]

looks great

[mario88ss]

:shock: SWEET ......La fiebre

[Rick88ss]

Thanks to everyone for the kind words.

SATAN wrote: That looks SOOO GOOOD! very clean too. What are your plans for your oil catch can? I see you currently have the outlet pointed toward the back of the bay???
I might put the oil catch can where the factory coil goes.I can swivel those fittings around easily

SATAN wrote: Who makes those coils? I love how you have 3 one one side and 3 on the other. Very nice job. very clean. I even like the knock off NISMO oil cap. I may have to get me one of those!
Those are Bosch coils made in Australia and sold with the Microtech.The oil cap...Ebay special

SATAN wrote: Wait a second, what are you going to do about a battery hold down now? Or is there still room behind that coil for one to fit?

Yeah the hold down fits.It's just laying there to the side for now.

SATAN wrote: Do you got a pic of the whole engine bay the way it sits right now? I can see you got some money sitting in all of those AN fittings. You did the same thing on your fuel rails that I did. As far as bolting them down I mean.

Here are some more pics.It's the same setup I had before except for the
individual coils.I also have to remove the rotor from the distributor and make some kinda cover plate.I only need the CAS.

[SATAN]

Nice, even with all of that crap in there, (power steering ac lines, half a distributor lol) still looks nice and simple. AND SO CLEAN I could eat out of that engine bay!

On your plenum, do the bolts being on top allow you to torqe them high enough and not crush in the top of the plenum? Do you have some sort of spacer inside to withstand the crushing?

Nice! I just noticed the red oil pan too!

very nice. Now just figure out that distributor issue

[MrwassmanNA2T]

just wait until that wiring harness gets in there

[BLOZ UP]

no VR sensor on the crank instead of the dizzy's CAS?

[mario88ss]

Cant' wait to hear that beach start up.











Wazzup....... La fiebre.

[Rick88ss]

Yeah the Microtech uses the factory CAS.No need to make some type of magnet crank position thing and bracket like the SDS.

[turbomike]

RE:

That does look gorgeous! Nice work painting the engine bay.

2 questions:

1 - where did you find the adjustable cam pulleys for the VG?

2 - did you do the plenum yourself? It looks very good. Do you know how it would compare with the pathy plenum?

Thanks,
Mike.

[SteveZ]

Re: RE:

turbomike wrote:
1 - where did you find the adjustable cam pulleys for the VG

http://www.Z31parts.com

[turbomike]

Damn! I can't believe I've never seen that site before!!!

That's all of the goodies I've been procrastinating about trying to make myself... awesome...